Biamp's SVC-2 card permits Biamp Tesira computerized signal processors to settle on and get telephone decisions over any Voice-over-IP (VoIP) framework that sticks to the SIP (Session Initiation Protocol) standard. This report subtleties the means needed to design a Cisco CallManager VoIP framework to work with Biamp's SVC-2 card.
Starter steps
TesiraVoIPMAC.jpgBefore arranging the cisco ccm, there is some data that should be gotten. To start with, note the MAC address of the SVC-2 card. To do this, first associate with the designed Tesira framework utilizing the Tesira programming. At that point, double tap on the VoIP Control/Status block and select the "Organization" tab. The MAC address of the SVC-2 card is recorded at the highest point of the page. Note that the MAC Address will possibly show up here in the event that you are associated live to the Tesira framework.
For forms more seasoned than 9.0: Cisco changed permit strategy from variant 9.0 onwards, so the beneath isn't significant for fresher adaptations. Yet, more established adaptations necessitated that the CallManager framework has enough licenses accessible to deal with a SVC-2. From CallManager's viewpoint, the SVC-2 card shows up as an outsider SIP endpoint. Cisco necessitated that an adequate amount of licenses be bought from them before an outsider SIP endpoint can be incorporated into the CallManager framework. To affirm this, sign in to the CallManager framework, and go to System—>Licensing—>License User Report. On the off chance that you intend to utilize the SVC-2 card for a solitary expansion, you will require 3 accessible licenses. On the off chance that you intend to utilize the SVC-2 card for two separate expansions, you will probably require 6 accessible licenses. In the event that uncertain, kindly contact Cisco to affirm the number of licenses are needed for your application.
Cisco arrangement
To begin with, we'll center around setting up the Cisco CallManager worker.
Security Profile
The initial step to setting up the CallManager framework is to make a Security Profile. In the event that your CallManager framework as of now has a current Security Profile that you'd prefer to utilize, you might have the option to avoid this progression, despite the fact that you ought to affirm that the current Security Profile has the settings depicted beneath. Follow the means underneath to make a Security Profile:TesiraCiscoSecurityProfile.jpg
Go to System—>Security—>Phone Security Profile.
Snap the "Add New" button.
Select the Phone Security Profile Type
In the event that you intend to utilize the SVC-2 card for a solitary augmentation, pick Third-party SIP Device (Basic).
In the event that you intend to utilize the SVC-2 card for two separate augmentations, pick Third-party SIP Device (Advanced).
Snap the "Following" button.
Enter a name and a depiction for the new Security Profile.
Leave the Nonce Validity Time at its default estimation of 600.
Set the Transport Type to either UDP or TCP (however not both). Tesira's default Transport type is UDP. Observe the vehicle type utilized, as it will be utilized later as the Transport setting in the SVC-2 card.
Snap the checkbox to Enable Digest Authentication.
Leave the SIP Phone Port at its default estimation of 5060 except if your specific circumstance requires SIP traffic to be communicated on an alternate port. If so, you'll need to indicate this port in the SVC-2 card also.
Snap the "Save" button.
Add another client
When an appropriate Security Profile has been made, another client should be made. Follow the means beneath to make another user:TesiraCiscoAddUser.jpg
Go to User Management—>End User.
Snap the "Add New" button.
Enter a client ID. Observe this User ID, as it will be utilized later as the "Confirmation User Name" in the SVC-2 card.
The secret phrase and PIN number are not needed.
Enter a Last Name (this name is for inside elucidating purposes as it were).
Enter a secret word in Digest Credentials. Observe the Digest Credentials secret key, as it will be utilized later as the "Confirmation Password" in the SVC-2 card.
Enter a similar secret word in "Affirm Digest Credentials".
The leftover fields on this page can be left either clear or at their default esteems.
Snap the "Save" button.
Add another gadget
When another client has been made, another gadget should be made. This gadget will connect to the Security Profile and the client made in before steps. Follow the means underneath to make another gadget:
TesiraCiscoAddDevice.jpg
cisco - audia- new device2 .jpg Tesira Cisco Assoc Info . jpg
TesiraCiscoDirNum.jpg
Go to Device—>Phone.
Snap the "Add New" button.
Select the Phone Type.
On the off chance that you intend to utilize the SVC-2 card for a solitary augmentation, pick Third-party SIP Device (Basic).
In the event that you intend to utilize the SVC-2 card for two separate augmentations, pick Third-party SIP Device (Advanced). Note that the Third-party SIP Device (Advanced) setting permits up to 8 lines, however the SVC-2 card utilizes a limit of 2 lines. This outcomes in a "mostly enrolled" message from Call Manager. This is ordinary and not a reason for concern.
Snap the "Following" button.
Information the MAC Address of the SVC-2 card. Note that the colons ought not be remembered for the MAC Address (see screen capture).
The Description field will auto-populate once the MAC Address has been entered.
Select the ideal Device Pool in which this gadget should be incorporated. Guarantee that the codec utilized by this gadget pool is upheld by the SVC-2 card (the SVC-2 card underpins the accompanying codecs: G.722, G.711μ, G.711A, G.729AB, and G.723.1).
The excess fields under the "Gadget Information" heading can be left at their default esteems.
For the Device Security Profile, pick the Security Profile made before.
For SIP Profile, pick "Standard SIP Profile".
For the Digest User, select the User made before.
The excess fields under the "Convention Specific Information" and "MLPP Information" headings can be left at their default esteems. In the event that you experience issues dialing DTMF digits from the SVC-2 card, you may have to check the "Require DTMF Reception" checkbox.
Snap the "Save" button.
No comments:
Post a Comment